Your submission was sent successfully! Close

Thank you for contacting us. A member of our team will be in touch shortly. Close

You have successfully unsubscribed! Close

Thank you for signing up for our newsletter!
In these regular emails you will find the latest updates about Ubuntu and upcoming events where you can meet our team.Close

Common multipath tasks and procedures

Note:
This documentation has moved to a new home! Please update your bookmarks to the new URL for the up-to-date version of this page.

This section shows examples of common configuration procedures and tasks. Before moving on with this section it’s a good idea to read or be familiar with the topics in these pages:

  1. Introduction to device mapper multipathing
  2. Configuration options and overview
  3. Configuration examples

For consistency, we will refer to device mapper multipathing as multipath.

Resizing online multipath devices

To resize online multipath devices, first find all the paths to the logical unit number (LUN) that is to be resized by running the following command:

$ sudo multipath -ll

mpathb (360014056eee8ec6e1164fcb959086482) dm-0 LIO-ORG,lun01
size=1.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=50 status=active
| `- 7:0:0:1 sde 8:64 active ready running
`-+- policy='service-time 0' prio=50 status=enabled
  `- 8:0:0:1 sdf 8:80 active ready running
mpatha (36001405e3c2841430ee4bf3871b1998b) dm-1 LIO-ORG,lun02
size=1.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=50 status=active
| `- 7:0:0:2 sdc 8:32 active ready running
`-+- policy='service-time 0' prio=50 status=enabled
  `- 8:0:0:2 sdd 8:48 active ready running

Now, reconfigure mpathb (with wwid = 360014056eee8ec6e1164fcb959086482) to have 2 GB instead of just 1 GB and check if it has changed:

$ echo 1 | sudo tee /sys/block/sde/device/rescan

1

$ echo 1 | sudo tee /sys/block/sdf/device/rescan

1

$ sudo multipath -ll

mpathb (360014056eee8ec6e1164fcb959086482) dm-0 LIO-ORG,lun01
size=1.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=50 status=active
| `- 7:0:0:1 sde 8:64 active ready running
`-+- policy='service-time 0' prio=50 status=enabled
  `- 8:0:0:1 sdf 8:80 active ready running
mpatha (36001405e3c2841430ee4bf3871b1998b) dm-1 LIO-ORG,lun02
size=1.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=50 status=active
| `- 7:0:0:2 sdc 8:32 active ready running
`-+- policy='service-time 0' prio=50 status=enabled
  `- 8:0:0:2 sdd 8:48 active ready running

Not yet! We still need to re-scan the multipath map:

$ sudo multipathd resize map mpathb

ok

And then we are good:

$ sudo multipath -ll

mpathb (360014056eee8ec6e1164fcb959086482) dm-0 LIO-ORG,lun01
size=2.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=50 status=active
| `- 7:0:0:1 sde 8:64 active ready running
.`-+- policy='service-time 0' prio=50 status=enabled
  `- 8:0:0:1 sdf 8:80 active ready running
mpatha (36001405e3c2841430ee4bf3871b1998b) dm-1 LIO-ORG,lun02
size=1.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=50 status=active
| `- 7:0:0:2 sdc 8:32 active ready running
`-+- policy='service-time 0' prio=50 status=enabled
  `- 8:0:0:2 sdd 8:48 active ready running

Make sure to run resize2fs /dev/mapper/mpathb to resize the filesystem.

Move root file system from a single path device to a multipath device

This is greatly simplified by the use of UUIDs to identify devices with an intrinsic label. To do this, install multipath-tools-boot and reboot your system. This will rebuild the initial RAM disk and afford multipath the opportunity to build its paths before the root filesystem is mounted by UUID.

Note:
Whenever multipath.conf is updated, initrd should be updated as well by running:
update-initramfs -u -k all
The reason for this is that multipath.conf is copied to the RAM disk, and is integral to determining the available devices to map via its denylist and devices sections.

The multipathd daemon

If you have trouble implementing a multipath configuration, you should ensure the multipath daemon is running as described in the example configuration page. The multipathd daemon must be running in order to use multipath devices.

Multipath command output

When you create, modify, or list a multipath device, you get a printout of the current device setup. The format is as follows for each multipath device:

action_if_any: alias (wwid_if_different_from_alias) dm_device_name_if_known vendor,product
   size=size features='features' hwhandler='hardware_handler' wp=write_permission_if_known

For each path group:

  -+- policy='scheduling_policy' prio=prio_if_known
  status=path_group_status_if_known

For each path:

   `- host:channel:id:lun devnode major:minor dm_status_if_known path_status
  online_status

For example, the output of a multipath command might appear as follows:

mpathb (360014056eee8ec6e1164fcb959086482) dm-0 LIO-ORG,lun01
size=2.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=50 status=active
| `- 7:0:0:1 sde 8:64 active ready running
`-+- policy='service-time 0' prio=50 status=enabled
  `- 8:0:0:1 sdf 8:80 active ready running

If the path is up and ready for I/O, the status of the path is ready or ghost. If the path is down, the status is faulty or shaky. The path status is updated periodically by the multipathd daemon based on the polling interval defined in the /etc/multipath.conf file.

The dm_status is similar to the path status, but from the kernel’s point of view. The dm_status has two states: failed, which is analogous to faulty, and active, which covers all other path states. Occasionally, the path state and the dm state of a device will temporary not agree.

The possible values for online_status are running and offline. A status of offline means that the SCSI device has been disabled.

Multipath queries with the multipath command

You can use the -l and -ll options of the multipath command to display the current multipath configuration.

  • -l : Displays multipath topology gathered from information in sysfs and the device mapper
  • -ll : Displays the information the -l displays in addition to all other available components of the system

When displaying the multipath configuration, there are three verbosity levels you can specify with the -v option of the multipath command:

  • -v0 : Yields no output
  • -v1 : Outputs only the created or updated multipath names, which you can then feed to other tools such as kpartx
  • -v2 : Prints all detected paths, multipaths, and device maps

Note:
The default verbosity level of multipath is 2 and can be globally modified by defining the verbosity attribute in the defaults section of multipath.conf

The following example shows the output of a sudo multipath -l command:

mpathb (360014056eee8ec6e1164fcb959086482) dm-0 LIO-ORG,lun01
size=2.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=0 status=active
| `- 7:0:0:1 sde 8:64 active undef running
`-+- policy='service-time 0' prio=0 status=enabled
  `- 8:0:0:1 sdf 8:80 active undef running
mpatha (36001405e3c2841430ee4bf3871b1998b) dm-1 LIO-ORG,lun02
size=1.0G features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=0 status=active
| `- 7:0:0:2 sdc 8:32 active undef running
`-+- policy='service-time 0' prio=0 status=enabled
  `- 8:0:0:2 sdd 8:48 active undef running

Determining device mapper entries with dmsetup

You can use the dmsetup command to find out which device mapper entries match the multipathed devices. The following command displays all the device mapper devices and their major and minor numbers. The minor numbers determine the name of the dm device. For example, a minor number of 1 corresponds to the multipathd device /dev/dm-1.

$ sudo dmsetup ls
mpathb  (253:0)
mpatha  (253:1)

$ ls -lahd /dev/dm*
brw-rw---- 1 root disk 253, 0 Apr 27 14:49 /dev/dm-0
brw-rw---- 1 root disk 253, 1 Apr 27 14:47 /dev/dm-1

Troubleshooting with the multipathd interactive console

The multipathd -k command is an interactive interface to the multipathd daemon. Running this command brings up an interactive multipath console where you can enter help to get a list of available commands, you can enter an interactive command, or you can enter Ctrl+D to quit.

The multipathd interactive console can be used to troubleshoot problems with your system. For example, the following command sequence displays the multipath configuration, including the defaults, before exiting the console.

$ sudo multipathd -k
  > show config
  > CTRL-D

The following command sequence ensures that multipath has picked up any changes to the multipath.conf:

$ sudo multipathd -k
> reconfigure
> CTRL-D

Use the following command sequence to ensure that the path checker is working properly:

$ sudo multipathd -k
> show paths
> CTRL-D

Commands can also be streamed into multipathd using STDIN like so:

$ echo 'show config' | sudo multipathd -k
Previous Configuration examples Next Reference

This page was last modified 2 months ago. Help improve this document in the forum.